3.8 Cutting Tools

There are several cutting tools on the right toolbar.

3.8.1 Polygon Cut

The Polygon Cut PIC tool allows you to build a polygon or an area with smooth borders that the cut area is projected on.

To build a polygon:

  1. Activate the Polygon Cut tool by clicking the left/right/middle mouse button. To continue work with this tool, use the button with which the tool was activated. To learn more about tool control, see Section 1.14.

  2. Click the mouse button to set the apices of the polygon marking the figure to be cut, except the last point.

  3. Fix the last point by double-clicking the mouse.

  4. To cancel an incomplete building, press Esc.

To build an area with smooth borders (Lasso mode):

  1. Activate the Polygon Cut tool by clicking the left/right/middle mouse button. To continue work with this tool, use the button with which the tool was activated. To learn more about tool control, see Section 1.14.

  2. Press and hold the Shift key on the keyboard.

  3. Circle the area to be cut, holding down the mouse button.

  4. To complete the building, release the mouse button or click another mouse button.

  5. To cancel an incomplete building, press Esc.

The part of the model to be projected on the area will be cut.

3.8.2 Inverse Polygon Cut

The tool is similar to the previous one, except that the part of the model not to be projected on the area will be cut. To activate/deactivate the tool, use the PIC button on the toolbar.

3.8.3 Cut object

The tool allows you to delete an area of a 3D model not associated with its other parts.

Activate/deactivate the PIC tool by clicking the left/right/middle mouse button. To continue work with this tool, use the button with which the tool was activated. To learn more about tool control, see Section 1.14.

3.8.4 Cut all except object

The tool is similar to the previous one, except that all areas excluding the selected area are deleted. To activate/deactivate the tool, use the PIC button on the toolbar.

3.8.5 Cutting Tools Parameters

For the Cut object and Cut all except object tools, the following parameters can be set:

  1. Grow from surface (mm). The tissue surrounding the deleted area will be deleted too. This parameter specifies the distance from the surface on which the tissue will be deleted. If this parameter is set to zero, the model surface may look rough, so use a value of zero only if necessary.

  2. Min object thickness (mm). If the value is greater than zero, the tissue with a thickness less than the set value will be ignored during deletion.

The parameters for each tool are set separately.

To set these parameters, click on the arrow on the right side of the appropriate tool button and select the Parameters... item and in the dialog box that appears, specify the required values.

3.8.6 Sphere Cut, Sphere Restore and Restore by Mask Tools

The Brush cut PIC , Brush restore PIC and Restore by mask PIC tools allow to remove tissue within a sphere or cylinder and restore the tissue deleted by cutting tools. To select one of these tools (Brush cut, Brush restore, Restore by mask) and modes (Sphere, Cylinder), click the arrow on the right side of the tool buttons. The button will look different depending on the tool that was used last:

The Brush restore and Restore by mask tools are assigned to the same button. To select a tool, click on the arrow on the right side of the tool selection button. The button looks different, depending on the tool selected:

PIC Brush restore (is selected by default)
PIC Restore by mask

To select one of modes (Sphere, Cylinder), click the arrow on the right side of the tool buttons. The same mode is chosen for Brush restore and Restore by mask tools.

The cursor will look different depending on the mode that is selected. The cursor for the Sphere mode is shown in Fig. 3.5, and the cursor for the Cylinder mode is shown in Fig. 3.6.


PIC

Figure 3.5: The cursor for Sphere mode

PIC

Figure 3.6: The cursor for Cylinder mode


To activate/deactivate the tool, click on the tool button. If any tool is activated, the button is highlighted.

To cut tissue:

  1. Activate the PIC Brush cut tool by clicking the left/right/middle mouse button. To continue work with this tool, use the button with which the tool was activated. To learn more about tool control, see Section 1.14.

  2. Set the tool diameter, moving the mouse while holding the Alt key. The Brush cut and Brush restore tools are set to the same diameter value.

  3. For the Cylinder mode, set the height if it is necessary. To do it, click the arrow on the right side of the tool button and select the Cylinder settings... item. In the dialog box that appears, set the cut height.

  4. Click the mouse button in the place where you want to cut tissue. Part of the tissue will be cut. The green dot indicates where the great circle of the sphere (the base area of the cylinder) touches the surface of the model. The great circle passes through the center of the sphere and is parallel to the plane of the screen.

  5. Repeat steps 2 and 4 if necessary.

The Brush restore PIC tool allows you to perform the reverse process of brush cutting.

The Restore by mask PIC tool allows you to restore tissue by mask (this tool is used for segmentation). If mask is not set, this mode is analogous to the Brush restore mode. For details how to set mask, see Section 6.2.4.

3.8.7 Tools for intelligent volume editing

____________________________________________________________________________________________

Functionality is available in the Pro edition
____________________________________________________________________________________________

The Grow (dilation), Shrink (erosion), Fill and Cut invisible volume tools allow to edit tissue within special algorithms. The Multi-segment growing (Voronoi diagram) tool allows you to edit segmented structures. To select one of these tools, click the arrow on the right side of the tool buttons. The button will look different depending on the tool that was used last:

PIC Grow (dilation) (set by default)
PIC Shrink (erosion)
PIC Remove noise (opening)
PIC Remove holes (closing)
PIC Multi-segment growing (Voronoi diagram)
PIC Fill
PIC Cut invisible volume

The Grow (dilation) tool allows you to increase the volume by a certain value from the surface in one iteration. This value is specified in the Settings menu of this tool (parameter Growing radius). The increase is possible only within the original volume, for example, after the use of cutting tools. When you use this tool to edit a segmented structure, an increase is possible only within the mask. The tool is used to fine-tune the structure if, initially, the required volume was not obtained.

The Shrink (erosion) tool performs the opposite action. The reduction value is specified by the parameter Growing/Shrinking radius.

The Remove noise (opening) tool allows to remove noise from the volume. This tool is equivalent to the consistently applied tools Shrink (erosion) and Grow (dilation).

The Remove holes (closing) tool allows to remove little holes from the volume. This tool is equivalent to the consistently applied tools Grow (dilation) and Shrink (erosion).

Each time the Grow (dilation), Shrink (erosion), Remove noise (opening), and Remove holes (closing) tools are used, a dialog box (Fig. 3.7), in which the operation radius should be set in millimeters or voxels is displayed.


PIC

Figure 3.7: Operation radius dialog box


The Multi-Segment Growing (Voronoi diagram) tool allows you to simultaneously build several structures and base volume. It is used to edit segmented structures (see Section 6.8.6). If the tool is applied only to the base volume, then it works like the Grow (dilation) tool.

The Fill tool allows you to fill the voids in the volume. If you are working with segmented structures, the tool is used to improve structures, built on a "grainy" mask. Such masks are typical, for example, for kidneys.

The Cut invisible volume tool sets the mask according to the visible volume.

3.8.8 Remove Table

The tool allows you to delete areas resembling the medical equipment table. To delete, click the PIC button on the toolbar.

PIC Some objects that have been misrecognized as the modality table may be deleted by mistake.

To undo or redo the last action associated with cutting, use the Undo PIC and Redo  PIC buttons.